+- (https://6mmarc.com)
+-- Forum: 6MMARC DISCUSSION (https://6mmarc.com/forumdisplay.php?fid=3)
+--- Forum: 6mmARC Bolt Actions (https://6mmarc.com/forumdisplay.php?fid=5)
+--- Thread: How much do you need ? (/showthread.php?tid=786)
How much do you need ? - Bassfish1952 - 10-17-2022
[attachment=562][attachment=563]
When mounting a scope how much do you need , I have the next size up mounts coming but do I need to use them ?
I have about 1/32 on the scope to barrel and a 1/8 on bolt to scope. This rifle has the different bolt that has been modified for clearance
Thanks
RE: How much do you need ? - grayfox - 10-17-2022
Scope to barrel is too close IMO. Scope to bolt... well there is most likely some slop in the bolt/receiver, so even there one could hit the other and scratch the scope. But the barrel end, that could affect barrel harmonics just like anything that touches the barrel during the shot.
I'd say, raise up the scope with some taller mounts. don't have a scientific number but at least 1/4" extra, I'd say.
RE: How much do you need ? - Bassfish1952 - 10-17-2022
(10-17-2022, 07:28 PM)grayfox Wrote: Scope to barrel is too close IMO. Scope to bolt... well there is most likely some slop in the bolt/receiver, so even there one could hit the other and scratch the scope. But the barrel end, that could affect barrel harmonics just like anything that touches the barrel during the shot.Thanks
I'd say, raise up the scope with some taller mounts. don't have a scientific number but at least 1/4" extra, I'd say.
I have the next higher Warne mounts coming but thought I would see how these were.
RE: How much do you need ? - Bassfish1952 - 10-17-2022
[attachment=564][attachment=565]
OK how about these they are Warne Maxima High rings for my rifle. I don't see anything higher than these on their site and I like the Warne Brand so .
RE: How much do you need ? - CZ527 Guy - 10-17-2022
In the end it is your choice, Id be content either way, Though Id have a fair preference with the lower option. If you can fit 3 thicknesses of paper between the barrel and the scope bell housing, Id feel good.
RE: How much do you need ? - Bassfish1952 - 10-17-2022
(10-17-2022, 10:20 PM)CZ527 Guy Wrote: In the end it is your choice, Id be content either way, Though Id have a fair preference with the lower option. If you can fit 3 thicknesses of paper between the barrel and the scope bell housing, Id feel good.Thanks
I'll try both and see how they do.
These old eyes do like the 3-9x50 a lot better than that 1.5-5. , was trying it just at dusk this one shows a lot better.
RE: How much do you need ? - grayfox - 10-18-2022
I like the higher setup personally. You can always pad up the top of buttstock or use a riser to get a new cheek weld if it's too high for your eyes to get center-eyepiece. That's what I do.
I'd rather have some wiggle room, it's just kind of SOP for me and my rifles.
Not out to win beauty contests, the critters in the forest don't mind either way lol!
RE: How much do you need ? - Bassfish1952 - 10-18-2022
Thanks Guys
I'm used to just buying and shooting , everything I have been doing this time is strange to me.
The opinions I have gotten from here have helped a lot
Thanks Again
RE: How much do you need ? - Dino11 - 10-18-2022
You have enough scope to barrel clearance, but the real question is how is your eye relief to scope, do you feel comfortable and not searching for a sight picture resting your cheek on the stock. This is what will dictate how high a scope mount you need. As long as your scope is not actually resting on the barrel, and it looks like in your picture you have more than enough room. Barrel harmonics at the chamber end of the barrel are nearly zero. Your picture looks like you have more than 1/32 scope clearance at the scope bell.
RE: How much do you need ? - Bassfish1952 - 10-27-2022
Thanks all . I went with the taller one for now . Going to try it hunting this year then see how I like it.